Waldorf Q+ Manuel d'utilisateur Page 34
- Page / 171
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Basic Operation – Editing Parameters
35 Waldorf Q User’s Manual
The procedure for setting up these parameters is the same as adjusting other display menu parameters
described above.
When you have finished all your edits, you should save the program. Please read the chapter about
storing programs on page 36 for further information.
Viewing Parameter Values without Change – Peek
The Q offers a special mode to check parameter values without performing any changes.
☞ To check parameter values without changing them:
1. Press the Peek button, located in the Master section. The LED beside this button will light
up.
2. If you move the control element of any panel parameter, its current value will be shown in
the display. E.g. if you move the Glide Rate knob in the Oscillators section, the display
will show (value may be different):
[Glide Rate 100]
3. After a few seconds, the display will return to its previous state. You can check several
parameters in the same way. You can also check the various display menu parameters.
Press the Edit button of a desired section and scroll through the display menu via the page
dial or by pressing the Edit button repeatedly. The same procedure is also valid for all
display menu parameters accessible via the Global, Multi, Matrix, Xphorm or Sound
buttons.
4. Press the Peek button again. The LED beside the button will go off, indicating that peek
mode has been terminated.
If you don’t check any parameters for a certain time, the Peek mode will be terminated
automatically. Independent from the Peek function the Peek LED lights up on any incoming
MIDI Message.
Comparing Edited Programs with Stored Programs
The Compare function allows you to compare the currently edited program to its original stored
version in the internal memory.
☞ To use the Compare function:
1. Choose the program type to compare as follows:
• If you want to compare a Sound, select the Play page or any of the Sound Edit
menus.
• If you want to compare a Multi, select the Multi page.
• If you want to compare a Sequencer Pattern, select the Step Sequencer Edit
menu.
• If you want to compare a Drum Map, select the Drum Map Edit menu.
2. Press Shift + Compare.
3. The display now shows a c after the program number:
- User´s Manual 1
- Q Keyboard/Q Rack/Q+ 1
- Garantiekarte / Warranty Card 2
- Foreword 4
- Front Panel Q Keyboard 5
- Frontpanel Q Rack 6
- Rear Panel 7
- Contents 8
- Introduction 10
- What to read? 11
- General Safety Guidelines 14
- Proper Use 15
- Setup and Connection 16
- ☞ To connect the devices: 17
- Audio Connections 18
- Digital S/PDIF Output 18
- External Input 19
- Switch Pedal Inputs 19
- Overview 20
- Memory Card 21
- Basic Operation 22
- Panic Function 23
- System Volume 23
- Demo Playback 23
- The Master Section 24
- Selecting Programs 24
- Multi Mode 25
- 78654321 90 26
- Bank Hold 27
- Switching Banks 27
- ☞ To select a card program: 28
- ☞ To select one instrument: 29
- Editing Parameters 30
- Editing Panel Parameters 31
- Control and Button Types 32
- ☞ To store a program: 35
- Instrument settings 38
- Volume 000…127 39
- Channel global, omni, 1…16 39
- LowKey C-2…G8 43
- HighKey C-2…G8 43
- Pattern off, 001…100 43
- Multi settings 44
- Multi Mixer 44
- Multi Tempo 40…300 45
- Step Sequencer 46
- Deselecting all Steps 47
- Programming Notes or Chords 47
- Programming a Pause 47
- ☞ To program a Hold event: 48
- Sequencer Panel Controls 49
- Sequencer Rotaries 50
- Sequencer Edit Menu 50
- Selection of a Pattern 51
- Option Line Parameter 51
- Pattern Length 1…32 52
- Transpose Key C-2…G8 52
- Rotate Steps 53
- Sound Parameters 54
- The Tempo 55
- Modulation Speed Levels 56
- Fast Modulation 57
- Standard Modulation 58
- Xphorm Edit Menu 62
- Triggering of Voices 63
- Oscillators 65
- The Sawtooth Wave 66
- The Square Wave 67
- The Pulse Wave 68
- The Triangle Wave 69
- Wavetable Synthesis 70
- Oscillators Panel Controls 71
- Detune -64…+63 72
- FM 0…127 72
- Pulsewidth 0…127 73
- PWM -64…+63 74
- Alt1 and Alt2 waveforms 75
- Sync Osc2 / Sync off / on 75
- PitchMod -64…+63 76
- Oscillators Edit Menu 77
- Glide Rate 0…127 78
- Glide / Active off / on 78
- Mixer Panel Controls 79
- Osc2 0…127 80
- Osc2 Balance F1 64…mid…F2 63 80
- Osc3 0…127 80
- Osc3 Balance F1 64…mid…F2 63 80
- RingMod 0…127 80
- Mixer Edit Menu 81
- Frequency 84
- Resonance 84
- Selecting and Editing Filters 85
- Filter Panel Controls 86
- Velo -64…+63 87
- Pan left 64…center…right 63 87
- Drive 0…127 87
- Filter Edit Menu 88
- Filter Types 89
- 24dB Notch and 12dB Notch 90
- The Comb filter as Chorus 92
- The Comb filter as Flanger 93
- 12dB/24dB Analog LP (Q+ only) 94
- Env Velo 95
- Amplifer Edit Menu 96
- Effect Panel Controls 97
- FX1 and FX2 Edit Menus 97
- Speed 0…127 98
- Depth 0…127 98
- Delay 0…127 98
- Overdrive 101
- Cutoff 0…127 102
- Overdrive 0…127 102
- Ring Mod 0…127 102
- Tap Delay 105
- 5.1 Delay 106
- 5.1 Surround Delay Types 106
- 5.1 D.Clk 108
- ☞ Building a Vocoder setup 109
- Bands 002…025 110
- S. Offset -64…+63 110
- Hi Offset -64…+63 110
- Arpeggiator 112
- Length 1/192…1/1 / legato 113
- Range 1 Oct…10 Oct 113
- Arpeggiator Edit Menu 114
- Max. Notes 1…16 115
- Clock 1/32t…1/1 115
- Length 1/192…127/192 / legato 115
- T. Factor 0…127 116
- Same Note Overlap Off / On 116
- Arp Timing ˆ / ¯…˛ 119
- Arp Steplen ˜ / ¯…˛ 120
- Envelopes 121
- ADSR Envelope 122
- ADS1DS2R Envelope 123
- One Shot 124
- Loop S1S2 125
- Loop All 126
- Shape Sync 127
- Speed Delay 127
- Shape Sync Speed Delay 127
- LFO Edit Menu 128
- Fade out 64…in 63 129
- Clocked Off / On 129
- Phase free, 000°…357° 129
- Modulation Matrix 130
- Modifier Matrix 131
- Control Delay 132
- Drum Map 133
- Key C-2…G8 134
- Transpose -60…+60 134
- Volume 0…127 134
- Global Parameters 135
- Tuning 430…450 Hz 137
- Transpose -12…+12 137
- HMT depth 000%...100% 138
- HMT MIDI Export off / on 138
- Ctrl W…Ctrl Z 0…120 139
- Input Gain 1…4 142
- Mix Level 0...127 143
- Operating System (OS) 143
- Pedal/CV1 Offset -64…+63 143
- ☞ To adjust Pedal/CV 1 Gain: 144
- Pedal/CV2 Gain 0...127 145
- Pedal/CV2 Curve 0...127 145
- Utility menu 146
- Init Drums 147
- Random Sound 147
- Rename Card 147
- MIDI Control 148
- Sending System Exclusive Data 151
- Other Functions 153
- The HMT function 155
- Tips & Tricks 156
- Appendix 157
- MIDI Signalflow Diagram 159
- Glossary 160
- Controller Numbers 164
- MIDI Implementation Chart 168
- Waldorf Q User’s Manual 170 169
- FCC Information (U.S.A.) 170
Produits connexes et manuels pour Synthétiseur Waldorf Q+
(22 pages)
(82 pages)
Synthétiseur Waldorf XTk Manuel d'utilisateur
(132 pages)
(132 pages)
© 2020, manymanuals.fr. Tous droits réservés | 3.968 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels