Waldorf Q+ Manuel d'utilisateur Page 135
- Page / 171
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Global Parameters – Global Menu
Waldorf Q User’s Manual 136
Global Parameters
Global parameters are settings that influence the Q’s general response. They are valid for all programs
but might be overridden by other more specific settings. Global parameters are stored automatically
when you modify them, so you are not required to save them manually.
Global Menu
All Global parameters are located in the Global Menu. Press the Master section’s Global button and
select the respective pages with the Page Dial or by pressing the Global button again. The menu
parameters are changed with the corresponding knobs below the display. Some parameters are only
available for the Q Keyboard (like pedal settings).
Glb.Chnl.!SysEx ID
01 !000 (00)
Global MIDI Channel (Glb.Chnl.) omni / 1…16
Sets the basic send and receive channel for the Q. This setting is valid for all Sound programs and for
Instruments of a Multi program whose Channel parameter is set to global. If omni is selected, the Q
sends on channel 1 and receives on all channels.
Please take special care when working in Multi Mode. In Multi Mode, the Q sends note data and
controller information on the channels set in the Instrument Channel parameter when the Instrument
Tx.Status is set to another value than off. With this function, it is easily possible to send up to 16
notes at once when you’ve pressed only one key.
Please use omni only for test purposes where you want to check the basic MIDI send and
receive functionality. As soon as you know that the Q receives MIDI properly, set Global
MIDI Channel to any other value than omni.
SysEx ID 0…126
Defines the device identification number for system exclusive data transmission. The number in
brackets shows the current ID in hexadecimal number format.
System Exclusive data contains no MIDI channel information so this ID is used to distinguish between
several Qs, if you have more than one Waldorf Q in your setup.
Transmission will only be executed successfully if the sender and receiver are set to the same SysEx
ID. ID 127 is a so-called broadcast ID that addresses all connected Qs. The Q can receive
broadcasted Sysex data from other devices, but cannot send it itself. This function is limited to special
computer software.
The Operating System upgrades are stored with ID 127 so you don’t need to change the Sysex
ID on your Q when you want to upgrade it to a newer OS.
If you have only one Q, leave Sysex ID on 0. There is no need at all to change this setting to
any other value.
After you bought your 128th Q please get in contact with Waldorf Electronics. You will
receive a personally ID number that authorize you to have a diner with our manager.
- User´s Manual 1
- Q Keyboard/Q Rack/Q+ 1
- Garantiekarte / Warranty Card 2
- Foreword 4
- Front Panel Q Keyboard 5
- Frontpanel Q Rack 6
- Rear Panel 7
- Contents 8
- Introduction 10
- What to read? 11
- General Safety Guidelines 14
- Proper Use 15
- Setup and Connection 16
- ☞ To connect the devices: 17
- Audio Connections 18
- Digital S/PDIF Output 18
- External Input 19
- Switch Pedal Inputs 19
- Overview 20
- Memory Card 21
- Basic Operation 22
- Panic Function 23
- System Volume 23
- Demo Playback 23
- The Master Section 24
- Selecting Programs 24
- Multi Mode 25
- 78654321 90 26
- Bank Hold 27
- Switching Banks 27
- ☞ To select a card program: 28
- ☞ To select one instrument: 29
- Editing Parameters 30
- Editing Panel Parameters 31
- Control and Button Types 32
- ☞ To store a program: 35
- Instrument settings 38
- Volume 000…127 39
- Channel global, omni, 1…16 39
- LowKey C-2…G8 43
- HighKey C-2…G8 43
- Pattern off, 001…100 43
- Multi settings 44
- Multi Mixer 44
- Multi Tempo 40…300 45
- Step Sequencer 46
- Deselecting all Steps 47
- Programming Notes or Chords 47
- Programming a Pause 47
- ☞ To program a Hold event: 48
- Sequencer Panel Controls 49
- Sequencer Rotaries 50
- Sequencer Edit Menu 50
- Selection of a Pattern 51
- Option Line Parameter 51
- Pattern Length 1…32 52
- Transpose Key C-2…G8 52
- Rotate Steps 53
- Sound Parameters 54
- The Tempo 55
- Modulation Speed Levels 56
- Fast Modulation 57
- Standard Modulation 58
- Xphorm Edit Menu 62
- Triggering of Voices 63
- Oscillators 65
- The Sawtooth Wave 66
- The Square Wave 67
- The Pulse Wave 68
- The Triangle Wave 69
- Wavetable Synthesis 70
- Oscillators Panel Controls 71
- Detune -64…+63 72
- FM 0…127 72
- Pulsewidth 0…127 73
- PWM -64…+63 74
- Alt1 and Alt2 waveforms 75
- Sync Osc2 / Sync off / on 75
- PitchMod -64…+63 76
- Oscillators Edit Menu 77
- Glide Rate 0…127 78
- Glide / Active off / on 78
- Mixer Panel Controls 79
- Osc2 0…127 80
- Osc2 Balance F1 64…mid…F2 63 80
- Osc3 0…127 80
- Osc3 Balance F1 64…mid…F2 63 80
- RingMod 0…127 80
- Mixer Edit Menu 81
- Frequency 84
- Resonance 84
- Selecting and Editing Filters 85
- Filter Panel Controls 86
- Velo -64…+63 87
- Pan left 64…center…right 63 87
- Drive 0…127 87
- Filter Edit Menu 88
- Filter Types 89
- 24dB Notch and 12dB Notch 90
- The Comb filter as Chorus 92
- The Comb filter as Flanger 93
- 12dB/24dB Analog LP (Q+ only) 94
- Env Velo 95
- Amplifer Edit Menu 96
- Effect Panel Controls 97
- FX1 and FX2 Edit Menus 97
- Speed 0…127 98
- Depth 0…127 98
- Delay 0…127 98
- Overdrive 101
- Cutoff 0…127 102
- Overdrive 0…127 102
- Ring Mod 0…127 102
- Tap Delay 105
- 5.1 Delay 106
- 5.1 Surround Delay Types 106
- 5.1 D.Clk 108
- ☞ Building a Vocoder setup 109
- Bands 002…025 110
- S. Offset -64…+63 110
- Hi Offset -64…+63 110
- Arpeggiator 112
- Length 1/192…1/1 / legato 113
- Range 1 Oct…10 Oct 113
- Arpeggiator Edit Menu 114
- Max. Notes 1…16 115
- Clock 1/32t…1/1 115
- Length 1/192…127/192 / legato 115
- T. Factor 0…127 116
- Same Note Overlap Off / On 116
- Arp Timing ˆ / ¯…˛ 119
- Arp Steplen ˜ / ¯…˛ 120
- Envelopes 121
- ADSR Envelope 122
- ADS1DS2R Envelope 123
- One Shot 124
- Loop S1S2 125
- Loop All 126
- Shape Sync 127
- Speed Delay 127
- Shape Sync Speed Delay 127
- LFO Edit Menu 128
- Fade out 64…in 63 129
- Clocked Off / On 129
- Phase free, 000°…357° 129
- Modulation Matrix 130
- Modifier Matrix 131
- Control Delay 132
- Drum Map 133
- Key C-2…G8 134
- Transpose -60…+60 134
- Volume 0…127 134
- Global Parameters 135
- Tuning 430…450 Hz 137
- Transpose -12…+12 137
- HMT depth 000%...100% 138
- HMT MIDI Export off / on 138
- Ctrl W…Ctrl Z 0…120 139
- Input Gain 1…4 142
- Mix Level 0...127 143
- Operating System (OS) 143
- Pedal/CV1 Offset -64…+63 143
- ☞ To adjust Pedal/CV 1 Gain: 144
- Pedal/CV2 Gain 0...127 145
- Pedal/CV2 Curve 0...127 145
- Utility menu 146
- Init Drums 147
- Random Sound 147
- Rename Card 147
- MIDI Control 148
- Sending System Exclusive Data 151
- Other Functions 153
- The HMT function 155
- Tips & Tricks 156
- Appendix 157
- MIDI Signalflow Diagram 159
- Glossary 160
- Controller Numbers 164
- MIDI Implementation Chart 168
- Waldorf Q User’s Manual 170 169
- FCC Information (U.S.A.) 170
Produits connexes et manuels pour Synthétiseur Waldorf Q+
(22 pages)
(82 pages)
Synthétiseur Waldorf XTk Manuel d'utilisateur
(132 pages)
(132 pages)
© 2020, manymanuals.fr. Tous droits réservés | 2.524 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels