Waldorf FNL8130G Spécifications

Installation and Operation Manual ‘Fast-Fri’ Gas Fryer FN8120G FN8226G FN8130G Date Purchased Serial Number Dealer Service Provider 228573-20 Fo

8 Installation Gas Connection NOTE: ALL GAS FITTING MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE PERSON. Flexible Hose Connection If a Gas Hose a

9 Installation 7. Check gas supply pressure is as shown in Specifications section, Gas Supply Requirements table. NOTE: Measure supply pressure at

10 Operation Operation Guide Description of Controls - (FN8120G Illustrated) This appliance is for professional use and is

11 Operation Filling the Tank(s) NOTE: WALDORF 'FAST-FRI' fryers can be used with both oil and shortening. 1. Before filling the tank, al

12 Operation Lighting Pilot Burners FN8120 Fryer (Single Tank) 1. Rotate gas control knob to Pilot position and hold knob depressed. 2. At the same

13 Operation Setting the Operating Temperature 1. Rotate thermostat to the required temperature. 2. Temperature can be set from 145°C to 195°C, alth

14 Cleaning and Maintenance General  To achieve the best results, cleaning must be regular and thorough and all controls and mechanical parts checke

15 Cleaning and Maintenance Opening the Drain Valve a. Lift locking slide on valve handle (Fig 12) to release valve. b. While holding locking slide

16 Cleaning and Maintenance Weekly Cleaning NOTE: If fryer usage is very high, we recommend that the weekly cleaning procedure is carried out more fr

17 Fault Finding Fault Possible Cause Remedy Frying medium foaming. Presence of soap or detergent residue from cleaning tank. Rinse fryer thoroughly

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in writing by the ma

18 Fault Finding Fault Possible Cause Remedy Rapid oil breakdown. Inadequate frying oil turnover. Adjust procedures to fry more food in fryer to in

19 Fault Finding Fault Finding the Gas System Fault Possible Cause Remedy Pilot Burners will not light. Gas supply is turned Off. Turn On gas suppl

20 Wiring Schematics FN8120G / FNL8120G Fryer - Single Tank TP THTHERMOSTATOVER TEMPTHTPIGNITIONTHERMOPILEL.H. PILOTT/CR.H. PILOTCROSS LIGHTINGT/CFLAM

21 Wiring Schematics FN8226G / FNL8226G Fryer - Double Tank THTP THTPMAIN GAS CONTROLSIT NOVA 820mVMAIN GAS CONTROLSIT NOVA 820mVPILOT PILOTT/CTHERMOP

22 Gas Conversion and Specifications Conversion Procedure NOTE:  These conversions should only be carried out by qualified persons. All connections

23 Gas Conversion and Specifications Gas Control Valve NOTE: For Twin Tank Fryers only, the units will be fitted with 2 gas control valves. These va

24 Gas Conversion and Specifications Gas Specifications NOTE: * Measure burner operating pressure at Operating Pressure Test Point (Lower - Out) on

25 Replacement Parts List Replacement Parts List When ordering spare parts, please quote part number and description as listed below. If part require

26 Replacement Parts List Gas Conversion Kits Accessories (Optional) 228793 450mm (Fryer) Plinth Kit. 228794 600mm (Fryer) Plinth Kit. Model Gas Ty

Contents FN(L)8120G ‘FAST FRI’ GAS FRYER (Single Tank - 20 Ltr) FN(L)8226G ‘FAST FRI’ GAS FRYER (Twin Tank - 26 Ltr) FN(L)8130G ‘FAST FRI’ GAS FRYE

2 Introduction We are confident that you will be delighted with your Waldorf 'Fast Fri' Gas Fryer, and it will become a most valued applianc

3 Specifications Model Numbers Covered in this Specification FN[1]8120G ‘FAST FRI’ GAS FRYER (Single Tank - 20 Ltr) FN[1]8226G ‘FAST FRI’ GAS FRYER

4 Dimensions FN(L)8120G / FN(L)8226G - GAS FRYERS FN(L)8120G Single Tank FN(L)8226G Twin Tank FN(L)8130G Single Tank FN(L)8130G - GAS FRYER 1. Prim

5 Installation Installation Requirements NOTE:  It is most important that this appliance is installed correctly and that operation is correct before

6 Installation Clearances NOTE:  Only non-combustible materials can be used in close proximity to this appliance.  To facilitate easy operation, d

7 Installation Fitting Rear Rollers. 1. Raise appliance from floor by approx. 75mm using suitable lifting equipment (i.e. Palletiser / Forklift) to a